Näytetään tulokset 1–20 / 26

  • Bosch Connect Module BCM3100 for BDU374YY

    99,00 

    Sopii:

    Performance Line CX (BDU3741)
    Performance Line CX Race Edition (BDU376Y)
    Cargo Line (BDU3741)
    Yhteensopiva älyjärjestelmän kanssa

    Haluaisitko asentaa ConnectModulen sähköpyörääsi ensimmäistä kertaa? Silloin tarvitset jälkiasennussarjan, joka sisältää asianmukaiset asennustarvikkeet.

    Kun Bosch Connect Modul asennetaan BDU33YY Drive Unitiin, vasen Design-kansi EB1120003X ja EB1120003U on korvattava Design-kannella EB1120003X.

  • Bosch virtakaapeli

    14,90 

    Tällä kaapelilla saat virtaa valoille ja muille laitteille. laita viestiin tiedot mihin käyttöön tulee. Gen 3 ja 4 ei smartsystem

  • Brose SPECIALIZED, Brose S ja Brose S-MAG

    99,00 

    Sähköpostilla Ei palautus oikeutta

  • DESIGN-KANSI PERFORMANCE LINE, VASEN, BCM (BDU33YY)

    19,90 

    Yhteensopiva älyjärjestelmän kanssa

    Kun Bosch Connect Modul asennetaan BDU33YY Drive Unitiin, vasen Design-kansi EB1120003X ja EB1120003U on korvattava Design-kannella EB1120003X.

    Toimituksen sisältö

    1 Design-kansi, vasen

  • SpeedBox 1 for Bafang MaxDrive keskimoottoreille 2019 ja vanhempiin

    165,00 

    SpeedBox 1.0 voit ohittaa 25km/h nopeusrajoituksen pyörästäsi ja voit nauttia pyöräsi moottorista aina 50km/h saakka. Asennuksen ja aktivoinnin jälkeen näyttö näyttää vain puolet todellisesta nopeusarvosta. SpeedBox 1.0 aktivointi ja deaktivointi suoritetaan painamalla lyhyesti ohjauspaneelin valopainiketta. Näytössä näkyy valosymboli, kun painat tätä painiketta. Tämä tarkoittaa, että SpeedBox on aktivoitu ja sähköpyörän moottorin tuki toimii jopa 50…

  • SpeedBox 1.0 B.Tuning for Bosch (Smart System)

    305,00 
    1. Virityssiru Bluetooth-tekniikalla ja mobiilisovelluksella sähköpyörällesi Bosch Gen4 -moottorilla ja Smart System -järjestelmällä. Nauti rajattomasta kyydistä ja kaikista SpeedBox-sovelluksemme tarjoamista mahtavista toiminnoista.

    SpeedBox B.Tuning tuo ainutlaatuisen yhteyden sähköpyörään ja matkapuhelimeen ja vaimentaa sähköpyöräsi nopeudenrajoitinta. Käytössä näytöllä näkyy todellinen nopeus 22,2 km/h asti. Tämän nopeuden ylityksen jälkeen todellinen nopeus näkyy näytön kahdessa viimeisessä numerossa.

    Esimerkki:

    – 22,3 vastaa nopeutta 23 km/h

    – 23,1 vastaa 31 km/h nopeutta

    Todellinen nopeus ja muut ajotiedot näkyvät oikein SpeedBox-sovelluksessamme – suoraan puhelimesi näytöllä.

    Miten SpeedBox 1.0 B.Tuning toimii?

    Jotta kaikki SpeedBoxin toiminnot aktivoituvat oikein, sinun on siirryttävä valikkoon ja vaihdettava pyöräsi ympärysmittaan e-pyörän kytkemisen jälkeen.

    Tämä virityssiru on myös erittäin helppo hallita. Aktivoi SpeedBox 1.0 B. Tuning mobiilisovelluksella tai suoraan sähköpyöräsi ohjausyksiköstä aktivoimalla WALK aputoiminnon hetken aikaa (pitämällä ”-”-painiketta painettuna). Sähköpyöräsi näytössä näkyy arvo 9,9 km/h (6,2 mph) ja tästä lähtien voit ajaa rajattomasti.

    Voit poistaa virityssirun käytöstä aktivoimalla WALK-aputoiminnon hetken kuluttua uudelleen (pitämällä ”-”-painiketta painettuna). Sähköpyöräsi näytössä näkyy arvo 2,5 km/h (1,6 mph) ja nopeusrajoitus nollataan 25 km/h. Sähköpyöräsi toimii tällöin samalla tavalla kuin ennen sirun asennusta.

    SpeedBox on suunniteltu myös sähköpyörille, joissa ei ole WALK-avustustoimintoa käytössä tai aktivoitu. Tässä tapauksessa voit aktivoida/deaktivoida virityksen vaihtamalla kahden aputilan välillä kahdesti, eli painamalla +-+- painikkeita.

    Kun avaat SpeedBox-sovelluksen ensimmäisen kerran, sinua pyydetään syöttämään uusi PIN-koodi. Tätä PIN-koodia kysytään aina, kun avaat SpeedBox-sovelluksen. PIN-koodin vahvistamisen jälkeen sinua pyydetään asettamaan huoltosalasana. Palvelusalasanaasi käytetään, jos unohdat PIN-koodin tai haluat vaihtaa sen.

    ”Latauslaskenta” jatkuu piilotettuna latauksen aikana, joten jos lataat sähköpyörääsi liitetyllä akulla, voit jättää huomiotta seuraavat ohjeet. Jos sinun on irrotettava akku sähköpyörästäsi sen lataamiseksi, sinun on odotettava, että SpeedBox suorittaa ”laskennan” ajon jälkeen. Kun pysäytät sähköpyöräsi, käynnissä oleva ”laskenta” ilmaistaan ​​lisääntyvällä ajoajalla. Kun ”lähtölaskenta” on suoritettu, ajoaika pysähtyy ja sähköpyörän näyttö näyttää oikean kuljetun matkan. Lähtölaskenta voidaan keskeyttää sammuttamalla ebike tai lähtemällä liikkeelle, joten se ei rajoita sähköpyöräsi käyttöä millään tavalla. Sinun on kuitenkin silti suoritettava laskenta säännöllisesti virityksen havaitsemisen estämiseksi.

    Kokoonpano

    Käytämme SpeedBox-sirujen valmistuksessa alkuperäisiä liittimiä, jotka varmistavat, että asennusprosessi on erittäin yksinkertainen ja siru on kytketty oikein. Olemme myös laatineet yksityiskohtaiset ohjeet ja videot asennuksen helpottamiseksi. Tuning-sirun purkaminen on yhtä helppoa. Jos sinulla on ongelmia asennuksen tai purkamisen kanssa, älä epäröi ottaa meihin yhteyttä.

    Jos aiot asentaa SpeedBoxin uuteen pyörään, varmista, että ajat sillä vähintään 1 km ennen kuin siru aktivoituu.

  • SpeedBox 1.0 for Bosch (Smart System)

    229,00 

    Virityspiiri sähköpyörille uusimmalla Bosch Gen4 -moottorilla ja Smart System -järjestelmällä.

    SpeedBox 1.0:n avulla voit vaimentaa sähköpyöräsi nopeudenrajoitinta. Käytössä näytöllä näkyy todellinen nopeus 22,2 km/h asti. Tämän nopeuden ylityksen jälkeen todellinen nopeus näkyy näytön kahdessa viimeisessä numerossa.

    Esimerkki:

    – 22,3 vastaa nopeutta 23 km/h

    – 23,1 vastaa 31 km/h nopeutta

    Jos haluat nähdä oikean nopeuden ja kaikki ajotiedot ajon aikana, suosittelemme valitsemaan SpeedBox 1.0 B.Tuning for Bosch. SpeedBox 1.0 B.Tuning for Bosch -sovelluksen avulla näet SpeedBox-sovelluksen todelliset arvot – suoraan puhelimesi näytöltä.

    Kuinka SpeedBox 1.0 toimii?

    Kaikkien SpeedBoxin toimintojen aktivoimiseksi oikein on välttämätöntä siirtyä valikkoon e-pyörän ensimmäisen päällekytkennän jälkeen viritysasennuksen jälkeen ja vaihtaa pyöräsi ympärysmittaan.

    Aktivoi SpeedBox 1.0 -virityssirun suoraan sähköpyöräsi ohjausyksiköstä aktivoimalla WALK-avustustoiminnon hetken kuluttua (pitämällä ”-”-painiketta painettuna). Sähköpyöräsi näytössä näkyy arvo 9,9 km/h (6,2 mph) ja tästä lähtien voit ajaa rajattomasti.

    Voit poistaa virityssirun käytöstä aktivoimalla WALK-aputoiminnon hetken kuluttua uudelleen (pitämällä ”-”-painiketta painettuna). Sähköpyöräsi näytössä näkyy arvo 2,5 km/h (1,6 mph) ja nopeusrajoitus nollataan 25 km/h. Sähköpyöräsi toimii tällöin samalla tavalla kuin ennen sirun asennusta.

    SpeedBox on suunniteltu myös sähköpyörille, joissa ei ole WALK-avustustoimintoa käytössä tai aktivoitu. Tässä tapauksessa voit aktivoida/deaktivoida virityksen vaihtamalla kahden aputilan välillä kahdesti, eli painamalla +-+- painikkeita.

    ”Latauslaskenta” jatkuu piilotettuna latauksen aikana, joten jos lataat sähköpyörääsi liitetyllä akulla, voit jättää huomiotta seuraavat ohjeet. Jos sinun on irrotettava akku sähköpyörästäsi sen lataamiseksi, sinun on odotettava, että SpeedBox suorittaa ”laskennan” ajon jälkeen. Kun pysäytät sähköpyöräsi, käynnissä oleva ”laskenta” ilmaistaan ​​lisääntyvällä ajoajalla. Kun ”lähtölaskenta” on suoritettu, ajoaika pysähtyy ja sähköpyörän näyttö näyttää oikean kuljetun matkan. Lähtölaskenta voidaan keskeyttää sammuttamalla sähköpyörä tai lähtemällä liikkeelle, joten se ei rajoita e-pyöräsi käyttöä millään tavalla. Sinun on kuitenkin silti suoritettava laskenta säännöllisesti virityksen havaitsemisen estämiseksi.

    Kokoonpano

    Käytämme SpeedBox-sirujen valmistuksessa alkuperäisiä liittimiä, jotka varmistavat, että asennusprosessi on erittäin yksinkertainen ja siru on kytketty oikein. Olemme myös laatineet yksityiskohtaiset ohjeet ja videot asennuksen helpottamiseksi. Tuning-sirun purkaminen on yhtä helppoa. Jos sinulla on ongelmia asennuksen tai purkamisen kanssa, älä epäröi ottaa meihin yhteyttä.

    Jos aiot asentaa SpeedBoxin uuteen pyörään, varmista, että ajat sillä vähintään 1 km ennen kuin siru aktivoituu.

    Varoitus

    Huomaa, että tämän tyyppisten muunneltujen sähköpyörien käyttö yleisillä teillä saattaa olla lainvastaista joissakin maissa. Valmistaja ei ota vastuuta vahingoista, jotka johtuvat SpeedBox-tuotteiden käytöstä. SpeedBox-tuotteilla varustettuja sähköpyöriä ei saa käyttää yleisillä teillä, pyöräteillä ja julkisilla paikoilla. SpeedBox-tuotteilla varustettuja sähköpyöriä saa käyttää yksinomaan yksityisellä kiinteistöllä ja täysin omalla vastuulla. SpeedBoxin käyttö voi mitätöidä ebikesi takuun.

    Suosittelemme vahvasti muiden turvaominaisuuksien ja suojavarusteiden käyttöä vammojen välttämiseksi.

     

     

  • SpeedBox 1.2 for Shimano (E8000, E7000, E6100)

    219,00 

    From the ground up redesigned tuning chip for your e-bike with a Shimano motor – with a new design and completely new hardware and firmware.

    The tuning chip SpeedBox 1.2 enables you to suppress the speed limiter on your electric bike. When in use, the actual speed will appear on your display up to 23 km/h.

    Compared to previous versions, this new product also plugs into the engine’s E-Tube port. It is therefore necessary that the e-bike motor in which you are going to install the new version of SpeedBox for Shimano has one free E-Tube port. It is not possible to install SpeedBox products for Shimano without a free E-Tube port in the engine.

    E-bikes, which do not have a free E-Tube port, are usually those with a Di2 electronic gear shifting system or with a wheel frame integrated Satellite System ON/OFF Switch (EW-SW100, EW-SW300).

    How does SpeedBox 1.2 work?

    This tuning chip can also be easily controlled with a LIGHT button. If the lights are turned off, SpeedBox is activated. The chip can be deactivated by turning on the lights. If you want to use tuning independently of the lights, do not connect the red wire during installation, like that the tuning will be always activated. If you do not have lights on your e-bike, SpeedBox 1.2 will also be activated at all times.

    Assembly

    We use original connectors for the production of SpeedBox chips ensuring that the installation process is very simple and the chip is connected properly. We have also prepared detailed instructions and videos to make installation easy for you. Disassembly of the tuning chip is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us.

    If you are planning to install SpeedBox on a brand-new bike, make sure you ride it for at least 1 km before the chip is activated.

     

  • SpeedBox 1.2 for Shimano (E8000, E7000, E6100) +E-Tube port

    219,00 

     

    +E-Tube port versio , pyörään jossa on erillinen käynnistin nappi.
    From the ground up   tuning chip for your e-bike with a Shimano motor – with a new design and completely new hardware and firmware.

    The tuning chip SpeedBox 1.2 enables you to suppress the speed limiter on your electric bike. When in use, the actual speed will appear on your display up to 23 km/h.

    Compared to previous versions, this new product also plugs into the engine’s E-Tube port. It is therefore necessary that the e-bike motor in which you are going to install the new version of SpeedBox for Shimano has one free E-Tube port. It is not possible to install SpeedBox products for Shimano without a free E-Tube port in the engine.

    E-bikes, which do not have a free E-Tube port, are usually those with a Di2 electronic gear shifting system or with a wheel frame integrated Satellite System ON/OFF Switch (EW-SW100, EW-SW300).

    How does SpeedBox 1.2 work?

    This tuning chip can also be easily controlled with a LIGHT button. If the lights are turned off, SpeedBox is activated. The chip can be deactivated by turning on the lights. If you want to use tuning independently of the lights, do not connect the red wire during installation, like that the tuning will be always activated. If you do not have lights on your e-bike, SpeedBox 1.2 will also be activated at all times.

    Assembly

    We use original connectors for the production of SpeedBox chips ensuring that the installation process is very simple and the chip is connected properly. We have also prepared detailed instructions and videos to make installation easy for you. Disassembly of the tuning chip is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us.

    If you are planning to install SpeedBox on a brand-new bike, make sure you ride it for at least 1 km before the chip is activated.

     

  • Ale!

    SpeedBox 1.3 Shimano EP8

    199,00 

    From the ground up redesigned tuning chip for your e-bike with a Shimano motor – with a new design and completely new hardware and firmware.

    The tuning chip SpeedBox 1.3 enables you to suppress the speed limiter on your electric bike. When in use, the actual speed will appear on your display up to 23 km/h.

    Compared to previous versions, this new product also plugs into the engine’s E-Tube port. It is therefore necessary that the e-bike motor in which you are going to install the new version of SpeedBox for Shimano has one free E-Tube port. It is not possible to install SpeedBox products for Shimano without a free E-Tube port in the engine.

    E-bikes, which do not have a free E-Tube port, are usually those with a Di2 electronic gear shifting system or with a wheel frame integrated Satellite System ON/OFF Switch (EW-SW100, EW-SW300).

    How does SpeedBox 1.3 work?

    If the lights are turned off, SpeedBox is activated. The chip can be deactivated by turning on the lights. If you want to use tuning independently of the lights, do not connect the red wire during installation, like that the tuning will be always activated. If you do not have lights on your e-bike, SpeedBox 1.3 will also be activated at all times.

    Assembly

    We use original connectors for the production of SpeedBox chips ensuring that the installation process is very simple and the chip is connected properly. We have also prepared detailed instructions and videos to make installation easy for you. Disassembly of the tuning chip is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us.

    If you are planning to install SpeedBox on a brand-new bike, make sure you ride it for at least 1 km before the chip is activated.

  • Ale!

    SpeedBox 1.3 Shimano EP8 tämä silloin jos kaikki portit on täynnä. +E TUBE port

    229,00 

    From the ground up redesigned tuning chip for your e-bike with a Shimano motor – with a new design and completely new hardware and firmware.

    The tuning chip SpeedBox 1.3 enables you to suppress the speed limiter on your electric bike. When in use, the actual speed will appear on your display up to 23 km/h.

    Compared to previous versions, this new product also plugs into the engine’s E-Tube port. It is therefore necessary that the e-bike motor in which you are going to install the new version of SpeedBox for Shimano has one free E-Tube port. It is not possible to install SpeedBox products for Shimano without a free E-Tube port in the engine.

    E-bikes, which do not have a free E-Tube port, are usually those with a Di2 electronic gear shifting system or with a wheel frame integrated Satellite System ON/OFF Switch (EW-SW100, EW-SW300).

    How does SpeedBox 1.3 work?

    If the lights are turned off, SpeedBox is activated. The chip can be deactivated by turning on the lights. If you want to use tuning independently of the lights, do not connect the red wire during installation, like that the tuning will be always activated. If you do not have lights on your e-bike, SpeedBox 1.3 will also be activated at all times.

    Assembly

    We use original connectors for the production of SpeedBox chips ensuring that the installation process is very simple and the chip is connected properly. We have also prepared detailed instructions and videos to make installation easy for you. Disassembly of the tuning chip is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us.

    If you are planning to install SpeedBox on a brand-new bike, make sure you ride it for at least 1 km before the chip is activated.

  • SpeedBox 2.1 for Giant

    209,00 

    SpeedBox 2.1 for Giant

     

  • SpeedBox 2.2 for Giant (RideControl Go)

    209,00 

    Luotettava toisen sukupolven virityspiiri sähköpyörille Giant 2022 Syncdrive Pro -moottorilla ja RideControl Go -näytöllä.

    SpeedBox 2.2 -virityssiru mahdollistaa sähköpyöräsi nopeudenrajoittimen vaimentamisen. Kun siru on asennettu, e-pyöräsi näytöllä näkyy todellisia tietoja, kuten maksimi- ja keskinopeus, päivittäinen mittarilukema ja matkamatka.

    Kuinka SpeedBox 2.2 toimii?

    Voit aktivoida SpeedBox 2.2 -virityssarjan sähköpyöräsi näytöllä. Kun olet painanut WALK / WALK UP, näytössä näkyy arvo 9,9 km/h (6,2 mph). Tästä eteenpäin voit ajaa rajattomasti – 30 km/h, 40 km/h ja yli 50 km/h.

    Poista siru käytöstä painamalla WALK / WALK UP. Näyttöön tulee arvo 2,5 km/h (1,6 mph) ja nopeusrajoitus palautetaan 25 km/h:iin. Sähköpyöräsi toimii tällöin samalla tavalla kuin ennen sirun asennusta.

    Kokoonpano

    Kun kytket SpeedBox-sirun sähköpyörään, löydät värilliset liittimet, jotka tekevät asennuksesta erittäin helppoa. Olemme laatineet yksityiskohtaiset ohjeet ja videot asennuksen helpottamiseksi. Virityssirun purkaminen on yhtä helppoa. Jos sinulla on ongelmia asennuksen tai purkamisen kanssa, älä epäröi ottaa meihin yhteyttä.

    Jos aiot asentaa SpeedBoxin uuteen pyörään, varmista, että ajat sillä vähintään 1 km ennen kuin siru aktivoituu.

    Lataa käsikirja
    Katso oikea johdinliitäntä

    Varoitus

    Huomaa, että tämän tyyppisten muunneltujen sähköpyörien käyttö yleisillä teillä saattaa olla lainvastaista joissakin maissa. Valmistaja ei ota vastuuta vahingoista, jotka johtuvat SpeedBox-tuotteiden käytöstä. SpeedBox-tuotteilla varustettuja sähköpyöriä ei saa käyttää yleisillä teillä, pyöräteillä ja julkisilla paikoilla. SpeedBox-tuotteilla varustettuja sähköpyöriä saa käyttää yksinomaan yksityisellä kiinteistöllä ja täysin omalla vastuulla. SpeedBoxin käyttö voi mitätöidä ebikesi takuun.

    Suosittelemme vahvasti muiden turvaominaisuuksien ja suojavarusteiden käyttöä vammojen estämiseksi.

  • SpeedBox 3.0 for Bosch Gen4

    189,00 

    OMINAISUUDET:
    Nopeusrajoitin: pois päältä
    Näyttö näyttää: todelliset arvot
    Yhteensopiva näyttöjen kanssa: KIOX, INTUVIA, NYON, PURION, COBI
    Yhteensopiva moottoreiden kanssa (sis. Gen4): Active Line Plus, Performance Line, Performance Line CX Line, Performance Line Speed, Cargo Line
    Ei yhteensopiva 2022 Bosch Smart Systemin kanssa
    Aktivointi: WALK-painike / + – + – / WALK +
    Yhteensopiva SpeedBox-sovelluksen kanssa: EI

    Kuinka SpeedBox 3.0 toimii?

    Virityssarja voidaan aktivoida suoraan pyöräsi näytöltä. Kävelypainikkeen painamisen jälkeen näytölle tulee arvo 9,9 km/h (6,2 mph), ja tästä lähtien voit ajaa nopeudella 40 km/h, 50 km/h ja jopa yli 60 km/h. .

    Voit poistaa virityssarjan käytöstä painamalla WALK-painiketta uudelleen. Näyttöön tulee arvo 2,5 km/h (1,6 mph) ja nopeusrajoitus palautetaan 25 km/h:iin. Sähköpyöräsi toimii sitten samalla tavalla kuin ennen sirun asennusta.

    SpeedBox on suunniteltu myös sähköpyörille, joissa ei ole klassista Walk-painikkeella varustettua ohjausyksikköä. Tässä tapauksessa voit vain käyttää + – + – -painikkeiden yhdistelmää ja SpeedBox aktivoituu. Voit helposti poistaa SpeedBoxin käytöstä samalla tavalla.

    Voit asettaa sähköavustimen maksiminopeuden vaihtamalla toimintatiloja: Turbo – EMTB – Tour – Eco – Tour – EMTB – Turbo. Todellinen nopeusrajoitus näytetään sen jälkeen. Sähköavustimen maksiminopeutta voidaan vaihtaa painamalla lyhyesti WALK-painiketta tai kääntämällä takapyörää 360°. Näytön arvo 1,5 km/h vastaa rajaa 15 km/h, 2 km/h vastaa rajaa 20 km/h, 2,5 vastaa 25 km/h, 3,0 vastaa. 30 km/h, 9,9 vastaa 99 km/h jne. Viimeinen näytetty raja tallentuu 5 sekunnin käyttämättömyyden jälkeen.

    Käytettäessä SpeedBox 3.0:aa Boschin 4. sukupolven moottoreiden kanssa (valmistettu vuonna 2020 tai myöhemmin), on välttämätöntä jättää pyörä päälle ajon päätyttyä, kunnes 0,0 km/h tulee näkyviin. Tämän prosessin aikana jäljellä oleva aika näytetään minuutteina. Sitten on turvallista sammuttaa pyöräsi ja voit alkaa odottaa seuraavaa matkaasi.

    Kokoonpano

    Kun kytket SpeedBox-sirun sähköpyörään, löydät värilliset liittimet, jotka tekevät asennuksesta erittäin helppoa. Olemme laatineet yksityiskohtaiset ohjeet ja videot asennuksen helpottamiseksi. Virityssirun purkaminen on yhtä helppoa. Jos sinulla on ongelmia asennuksen tai purkamisen kanssa, älä epäröi ottaa meihin yhteyttä.

    Jos aiot asentaa SpeedBoxin uuteen pyörään, varmista, että ajat sillä vähintään 1 km ennen kuin siru aktivoituu.

     

    Huomaa, että muutettujen sähköpyörien toiminta julkisilla teillä on suomessa lain vastainen. Valmistaja ja jälleenmyyjä ei vastaa SpeedBox -tuotteiden käytöstä aiheutuvista vahingoista. SpeedBox -tuotteilla varustetut sähköpyörät eivät ole sallittuja julkisilla teillä, pyöräilyreiteillä ja julkisilla paikoilla. SpeedBox -tuotteilla varustettuja sähköpyöriä voi käyttää yksinomaan yksityisomistuksessa ja täysin omalla vastuulla. SpeedBox: n käyttö voi mitätöidä sähköpyörän takuun.

  • SpeedBox 3.0 for Brose ribelle

    199,00 

    Varoitus

    Huomaa, että tämän tyyppisten muunneltujen sähköpyörien käyttö yleisillä teillä saattaa olla lainvastaista joissakin maissa. Valmistaja ei ota vastuuta vahingoista, jotka johtuvat SpeedBox-tuotteiden käytöstä. SpeedBox-tuotteilla varustettuja sähköpyöriä ei saa käyttää yleisillä teillä, pyöräteillä ja julkisilla paikoilla. SpeedBox-tuotteilla varustettuja sähköpyöriä saa käyttää yksinomaan yksityisellä kiinteistöllä ja täysin omalla vastuulla. SpeedBoxin käyttö voi mitätöidä ebikesi takuun.

    Suosittelemme vahvasti muiden turvaominaisuuksien ja suojavarusteiden käyttöä vammojen estämiseksi.

    PROPERTIES:
    Activation: WALK function/ + – + –
    Maximum speed: unlimited
    Speed limit setting: YES
    Display shows: actual values
    Compatible with motors:
    Brose SPECIALIZED (except for SL models)
    Brose S-MAG
    Brose S
    Brose T
    Not compatible with:
    motors Brose S Mag FIT
    SpeedBox App

    In case of updating the software of your e-bike, uninstall SpeedBox from the e-bike first, update the software and reinstall SpeedBox.

  • Ale!

    SpeedBox 3.0 for Yamaha

    199,00 

    SpeedBox 3.0 virityspiiri mahdollistaa nopeusrajoituksen valitsemisen itse. Kun siru on asennettu, sähköpyöräsi näyttö näyttää todellista tietoa, kuten maksimi- ja keskinopeudet, päivittäiset kilometrit ja ajomatka.

    Ominaisuudet:

    • Activation: LIGHT button / ↑↓↑↓ / + – + –
    • Maximum speed: unlimited
    • Speed limit setting: yes
    • Display shows: actual values

    Yhteensopiva moottoreiden kanssa:

    • PW-SE
    • PW-X
    • PW-TE
    • PW-CE
    • PW-X2
    • PW-ST vuoteen 2021 asti

    Ei yhteensopiva sähköpyörien ja moottoreiden kanssa:

    • Yamaha UrbanRush
    • CrossCore
    • CrossConnect
    • Wabash
    • PW-X3
    • YDX-Torc
    • YDX-Moro
    • YDX-Moro Pro
    • PW-ST vuodesta 2022

    In case of updating the software of your e-bike, uninstall SpeedBox from the e-bike first, update the software and reinstall SpeedBox.

  • SpeedBox 3.1 for Bafang MaxDrive keskimoottoreille. 2020 ja uudempiin

    179,00 

    https://youtu.be/n9GaBxTUd_I?t=5

  • Speedbox Panasonic

    165,00 

    Evo for Panasonic GX0, X0, X1, GX Ultimate, GX Power Plus e GX Power

  • Speedfun Evo rocky Mountain

    159,00 
  • SpeedFun Furious Evo (kytkeytyy valokytkimestä) for Brose & Continental

    170,00 

     

    What is SpeedFun Furious Evo ebike tuning for Brose and Continental?

    The function of the Furious Evo tuning device for Brose and Continental is to electronically manipulate the rotation speed of the rear wheel and to communicate to the motor a speed always lower than 25 KmH in order to obtain a real speed with very high active motor. The maximum speed limit will therefore be dictated by the power of the engine added to the power expressed by one’s legs (info).

    When the tuning device is active, having no communication with the display, it will show the halved data on the display starting from a certain threshold.

    SpeedFun Furious Evo can be activated and deactivated at will and maintains the setting even after the ebike is turned off. It can be installed on ebike with Brose in aluminum (Brose C, Brose T, Brose TF, Brose S) or with Brose engines in magnesium (Brose S Mag) and Continental motors mostly mounted on ebike Axevo, Bergstrom, Besv, BH, Bikel, BMW, Bulls, Campus, Cheetah, Cucuma, Devinci, Diavelo, Douze Cycles, e-Framer, Elops, Fantic, Fischer, FXX Cycles, Head, Hercules, Innata, Kraft Stoff, Leaos, LeeCougan, Olmo, Olympia, M1 Sport Technik, Maxx, Nox Cycles, Neomuv, NSR, Pedal Power, Pedego, Pininfarina, Poison, Pragma Industries, QWIC, Rockrider (Decathlon), Rotwild, Sblocs, Specialized, Sunn, Triobike, VKT regardless of the type of display or side control of the ebike.

    The Furious Evo tuning device for Brose and Continental is available in two versions:

    • – Easy version: supplied already active, it can in any case be activated/deactivated with a very practical system (for more information see the instructions)
    • – On/off lights version: can be activated/deactivated by simply pressing the lights button of the ebike. In this case it is necessary to make sure that the ebike has the lights button and that no lights are installed.

    The device is supplied plug and go ready to use and is installed in a very simple way thanks to the compatible connectors with which no physical modification of the ebike is necessary.

     

    Ebike with Brose and Continental engine where the Furious Evo device was successfully installed

    (this list is illustrative and not exhaustive)

     

    – Rotwild R.X750
    – Specialized Turbo Levo 2020 e 2021

     

    – Fantic xf1 integra 160

     

     

    The main features

    – Totally invisible

    – It can be assembled/disassembled at any time

    – Equipped with compatible connectors that do not require any physical modification to the ebike wiring

    – Allows you to remove the 25 KmH limit up to unlimited speeds (info)

    – Installable in a few minutes, ready to use, plug and go!

    – Suitable for Brose and Continental motors mounted mostly on ebike Axevo, Bergstrom, Besv, BH, Bikel, BMW, Bulls, Campus, Cheetah, Cucuma, Devinci, Diavelo, Douze Cycles, e-Framer, Elops, Fantic, Fischer, FXX Cycles, Head, Hercules, Innata, Kraft Stoff , Leaos, LeeCougan, Olmo, Olympia, M1 Sport Technik, Maxx, Nox Cycles, Neomuv, NSR, Pedal Power, Pedego, Pininfarina, Poison, Pragma Industries, QWIC, Rockrider (Decathlon), Rotwild, Sblocs, Specialized, Sunn, Triobike , VKT and many more

    – Compatible with any type of display or command

    – It is possible to activate/deactivate the device by pressing the lights button (in the on/off light versions) or in a very practical way (in the easy version). More info in the instructions.

    – It does not need external batteries or power